frequency coefficient of rated ripple current coefficient frequency 50 hz 0.70 ub series chip type, high reliability chip type, high temperature range, for +125? use. applicable to automatic mounting machine fed with carrier tape. compliant to the rohs directive (2011/65/eu). specifications performance characteristics item ub ux voltage capacitance 125c marking lot no. plastic platform 0.3max. d0.5 b0.2 a 0.2 a0.2 c0.2 0.5max. e h h positive negative plastic platform pressure relief vent 0.3max. d0.5 b0.2 a 0.2 a0.2 c0.2 0.5max. e positive negative u 1 u 2 b 3 1 4 a 5 1 6 0 7 1 8 m 9 c 10 l 11 1 12 g 13 s 14 configuration taping code capacitance tolerance ( 20%) rated capacitance ( 100f ) rated voltage ( 10v ) series name type d l 8 6.2 8 10 code cl nl 10 10 nl l0.3 l0.5 8 6.2 d l a b c e 3.3 8.3 8.3 2.3 8 10 2.9 8.3 8.3 3.1 10 10 3.2 10.3 10.3 4.5 l 6.2 10 10 h 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 (mm) voltage capacitance lot no. trade mark trade mark 125 c marking a2e 330 10v a2e 100 10v chip type ( 8 6.2) ( 8 10, 10 10) type numbering system (example : 10v 100 f) rated ripple current (marms) at 125 c 120hz dimensions 010 022 033 047 100 220 330 100 220 330 470 101 221 331 8 6.2 8 10 10 10 8 10 10 10 8 6.2 8 10 10 10 8 6.2 8 10 10 10 8 6.2 8 6.2 8 10 10 10 58 90 112 66 102 48 74 116 44 52 80 24 38 46 58 1a 1c 1e 1v 1h 10 16 25 35 50 v code cap.(f) rated ripple high temperature aluminum electrolytic capacitors cj added esr specification at 40 c wh high temperature reflow lt high voltage taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please refer to page 3 for the minimum order quantity. case size d l (mm) category temperature range 40 to +125 c rated voltage range 10 to 400v rated capacitance range 1 to 330f 20% at 120hz, 20 c capacitance tolerance measurement frequency : 120hz the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 2000 hours (1000 hours for 8 6.2 ) at 125 c. z 40 c / z+20 c rated voltage (v) impedance ratio zt / z20 (max.) 10 12 16 8 25 6 35 4 50 4 rated voltage (v) tan (max.) 10 0.32 16 0.24 25 0.21 35 0.18 50 0.18 measurement frequency : 120hz at 20 c capacitance change leakage current tan within 30% of the initial capacitance value less than or equal to the initial specified value 300% or less than the intial specified value leakage current tangent of loss angle (tan ) stability at low temperature endurance the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c. the capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20 c. black print on the case top. after storing the capacitors under no load at 125 c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the specified values for the endurance characteristics listed above. capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value shelf life resistance to soldering heat marking rated voltage (v) 10 to 50 160 to 400 after 1 minute's application of rated voltage, leakage current is not more than 0.03cv (a). i = 0.04cv+100 ( a) max.(1 minute's) leakage current 160 0.30 200 0.30 250 0.30 400 0.30 160 8 200 8 250 8 400 12 1 1.8 2.2 3.3 4.7 6.8 10 010 1r8 2r2 3r3 4r7 6r8 100 8 10 10 10 42 59 2c cap.(f) v 160 code 8 10 10 10 10 10 2d 200 8 10 8 10 10 10 10 10 26 27 36 38 2g 400 8 10 10 10 36 59 59 28 59 2e 250 1.00 1.17 1.36 1.50 120 hz 300 hz 1 khz 10 khz or more (through 50v only) rated ripple case size d l (mm) cat.8100c
|
